HYDRAULIC AND MECHANICAL
Disc brakes fall into two categories:
hydraulic and mechanical. Squeezing the brake lever of a hydraulic disc
brake system pushes a piston that pressurizes brake fluid running
through a hose to a brake caliper mounted to your bike’s frame or fork.
Once the increased pressure reaches the caliper, it presses the disc
brake pads against a brake rotor. Mechanical disc brakes do the same
thing, except instead of using brake fluid pressurized in a hose, a
cable from the brake lever to the brake caliper actuates the brake pads
by rotating some type of cam.
START WITH THE OBVIOUS
Before you mess with replacing brake
pads, truing rotors or stacking shims, make sure your wheels are
properly installed in the fork and frame. A paint chip, dirt or a
wayward quick-release spring will wreak havoc on braking performance.
Pull the wheel out, inspect the dropout, replace the wheel and snug the
quick release. This will fix 37 percent of all brake noise problems.
Warning: Disc brakes work by converting the speed and energy of the bicycle into heat. When you have been on your brakes hard, they will generate a significant amount of heat (in the rotor, pads, caliper and even brake fluid). So, before touching any part of your brake system, make sure it has cooled down.
The gloves come off: Clean the brake rotors with a damp cloth (moistened with isopropyl-alcohol). The gloves were removed to prevent oil or grease residue from ending up on the disc. Reduce the chance of injury by removing the wheel for cleaning.
Clean surface: Look for obvious problems before you start pulling brake pads to cure noise. Make sure the dropouts are clean. Look for chipped paint or a damaged surface that could cause the wheel to set improperly. This dropout is perfect.
We highly recommend that your tool box contain a few spare brake pads at all times. Brake pads wear differently depending on the material they are made from, the conditions you ride in and the way you apply your brakes. Some riders can get a year’s use out of a single set of brake pads, while a more aggressive rider in nasty conditions might go through brake pads monthly. Either way, when brake pads finally reach their limit, it happens quickly. Having that spare set in the box might be the difference between riding tomorrow and waiting for pads to show up in the mail. Order a set today.
Snug it up: Another culprit of brake rubbing could be loose mounting hardware. Most disc brakes require a Torx T-25 wrench (available at any hardware store) to snug the hardware. It is a good idea to keep an eye on these bolts, even if rubbing is not an issue.
Brake pads for both mechanical and hydraulic systems are available in various compounds. Generally, a softer organic (or resin) material will tend to make less noise during operation and will offer more modulation. These guys wear out the fastest. Metallic (or semi-metallic) pads will last longer, especially in wet and muddy conditions. Mixing the pads (one metallic and one organic) can have favorable braking results but will require more attention (because the organic pad will wear faster than the metallic pad).
You know the rotor is clean, true and secure, but
there is still a scraping noise when you spin the wheel. It is time to
take a look at the brake pads.
1) Pull the wheel out and inspect the
brake pads for dirt, damage and wear. Comparing them to your new set
makes it easier to identify problems.
2) You may need to remove the
brake pads for proper inspection. You will need the owner’s manual to
properly remove and replace them. A rule of thumb is if the pads are
less than three millimeters thick (this includes the backing plate),
3) We have traced brake noise to a damaged brake pad
spring (that little cage that surrounds the brake pads when they clip
into the brake caliper), so don’t overlook it.
Open-system hydraulic brakes self-adjust
for wear. Occasionally, the pads will move too close to the rotors and
drag against them. Many times, the caliper needs to be reset because
somebody squeezed the brake lever when a wheel was out of the frame.
Here’s what to do:
1) If the pads are in good shape, carefully insert
the blade of a clean, wide, flat screwdriver (with a relatively sharp
tip) between the pads. Work the blade past the center of the caliper
pistons and pry the pads apart by twisting the handle until you have
retracted the caliper pistons well past the thickness of the brake
2) Reinstall the wheel. Take two business cards and slide one between the brake pad and the rotor on each side of the rotor.
Make sure your bike is upright. Squeeze the brake lever until the
master cylinder pumps enough fluid into the calipers to return the pads
to their correct position (the levers feel firm when you squeeze them).
4) Pull the cards out and pump the brake lever lightly a few more times.
you use a mechanical disc brake, adjusting the cable tension will
accomplish pretty much what we just did with the hydraulic brake.
Push’em apart: If the pad clearance is very narrow (Photo A above), take a screwdriver, carefully slide it between the pads and twist the handle (Photo B). Never force the screwdriver, because you could gouge the pad
surface, reducing its life. After you do this, the pads are fully seated
and ready for the disc (Photo C).
Brake rotors inflict more injuries on mountain bikers every year than that unexpected rock drop near the top of Upper A-Line at Whistler Mountain Bike Park. Never put your fingers near the rotor when spinning the wheel. Even professional mechanics have lost finger tips to a spinning brake rotor. You can suffer an injury even while wearing gloves. If you are tired, bored or distracted, leave the brake servicing for another time.
Bend it back: Eyeball the rotor spinning through the caliper. If the rotor is bent, use a tool like the Park Tools DT-2 Rotor Truing Fork to correct the wayward wobble. The disc is fairly flexible, so don’t overdo it. A little pressure does a lot.
Wear them down: Once brake pads wear to less than three millimeters thick (including the backing plate), it is time to slap a new set in.
Take my card: Hold a business card on each side of the rotor and carefully rotate them into the brake caliper. Squeeze the brake a few times. Pull the cards out. This trick has been used to silence millions of rubbing brakes.
Pad inspection: If necessary, pull the brake pads (follow your owner’s manual instructions) and look for excessive or uneven wear. Inspect for damage or contamination to the pad surface. Check the spider spring (they can produce unwanted noise if damaged or worn).
NOT YET CURED
Still got a rubbing noise? Your brake caliper uses either shims or a bracket with a small amount of adjustment for fine tuning its relationship to the brake rotor.
1) With the wheel in the bike and the bike on a stand, rotate the wheel and look down the line where the rotor enters the caliper. Is the caliper pretty well centered over the rotor?
2) If not, you need to add or remove shims or loosen the caliper’s mounting hardware to position the caliper correctly. This takes trial and error and patience. Sometimes, you may get the caliper perfect, but snugging the hardware throws it off. Again, take your time.
3) If you have to use more than two or three shims to position the caliper correctly, you may have mounted the caliper or mounting hardware incorrectly. The frame or fork may also need facing where the hardware or caliper mounts. A bike shop will have to help you with this.
The Garage Files is a monthly feature of Mountain Bike Action. The following links will take you to more Garage Files.
Spending Time Behind Bars, Click Here.
Drivetrain Tips, Click Here.
Bike Action is a monthly magazine
Publishing in Valencia, California. It has been published since
1986. You can start a subscription by clicking
here or calling (800) 767-0345.